Formfutura - BVOH - 300g


Le filament d'imprimante BVOH - Butenediol Vinyl Alcohol Co-polymer - de FormFutura est un matériau de support avancé hydrosoluble pour l'impression 3D multi-extrusion complexe. Le BVOH adhère à presque tous les «matériaux de construction» et se dissout dans l'eau plus rapidement que les matériaux de support PVA. Sa stabilité thermique est optimisée pour éliminer tout risque de colmatage de votre hot-end par dégradation thermique.

Caractéristiques uniques

  • Bonne adhérence avec presque tous les matériaux
  • Excellente solubilité dans l'eau
  • Résistant à la dégradation thermique grâce à des propriétés de fusion optimisées
  • Respectueux de la nature

5 Produits
Diamètre du filament
39,26 € HT / 47,50 € TTC
En stock


  • Reliable multi-extrusion 3D printing of complex structures that require a water-soluble support material

    • 3D printing geometries with large overhangs or complex hollow structures

  • PVA molds

General printing guidelines

Nozzle side: ≥ 0.15mm layer height: ≥ 0.1mm Experience level: Expert
Print temp: ± 200 - 230° C * Fan speed: 0 - 30%
Heat bed: ± 65 - 75° C Enclosure needed: No

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these parameters if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends, and printer offset that it is extremely difficult to give an overall one-size-fits-all setting.

*) Do not exceed a printing temperature of 230˚C for a prolonged period of time.

*) Once BVOH has been used or opened from its original vacuum-sealed packaging for a while it is advised to dry the material before using again.     

Filament length

ρ: 1.14 g/cc 50 gr coil 0.3 Kg spool 0.75 Kg spool
Ø 1.75mm ± 18.2m ± 109m ± 274m
Ø 2.85mm ± 6.9m ± 41m ± 103m

General guidelines for 3D printing with support materials like PVA and BVOH

Printing with support materials, in general, isn’t plug and play and does require a fair amount of 3D printing expertise as there isn’t a generic one-size-fits-all setting for multi extrusion 3D printing with PVA and/or BVOH filaments. The optimal 3D printing settings for support PVA and BVOH filaments can even vary between the same models of 3D printers.

One of the most common challenges is to establish a good bond between the PVA and/or BVOH support material and the primary build material. Below parameters are of utmost importance to establish good bonding between the 3D printing materials.

  • Verify the extrusion distance between the printed object and the support material.

    • Typically the default setting in most slicer software is set at an extrusion distance of 0.1 - 0.2mm, which is optimal for break-away support materials. For water-soluble support materials, we recommend turning this setting down to 0.0mm.

  • The displayed printing/nozzle temperature should be accurate.

    • If the temperature deviates up to or over 10°C from the intended printing temperature, this may negatively impact the flow of your support material. How big this deviation is wildly varies depending on the printer you're using.

  • Make sure your printer is properly leveled. Avoid height differences across the multiple nozzles.

    • To verify your nozzles are leveled, we recommend 3D printing a small rod (e.g. 5cm x 1cm with PLA) and switching nozzles every 1 - 2 layers to detect any imperfections in the layers. 

Product export information

HS Code: 39169090 Description: Monofilament Country of origin: the Netherlands


This filament is compliant to the directives and regulations listed below:

  • RoHS directive 2011/65/EC

  • REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above-described products.

5 Produits

Fiche technique

Matériau BVOH
Poids (net) 300 g
Gamme BVOH
chat Commentaires (0)
Aucun avis n'a été publié pour le moment.